Mfg. Journalist Cutler Profiles ETO Manufacturing Issues in Quality Digest Technology Articles | September 22 Jahlil Okafor Blue Devils Jersey , 2005 Quality Digest online profiles Engineer-to-Order Manufacturing and a rundown of its different set of quality standards and tools.The feature article can be found at www.trcutlerinc. In the increas...
Quality Digest online profiles Engineer-to-Order Manufacturing and a rundown of its different set of quality standards and tools.
The feature article can be found at www.trcutlerinc. In the increasingly competitive world of engineer-to-order and project-based manufacturing, companies have to operate at maximum efficiency to compete with not only domestic, but also the growing number of overseas competitors. The companies that will thrive in this environment are those that are continually looking for improvement.
According to Cutler, the author of the feature article R. J. Barrett Blue Devils Jersey , "In repetitive manufacturing you can apply Statistical Process Control (SPC) techniques to purchased components and manufacturing quality as well as scrap and yield.
Statistical analysis is acceptable if a company is mass purchasing or mass manufacturing the same product to the same standards every time. The essence of ETO is building a unique complex product every time. There may be components that are common from one machine to another, but not in the same quantity as a repetitive manufacturer." Cutler profiles several Encompix ERP clients in the feature article.
Thomas R. Cutler, President & CEO of Fort Lauderdale, Florida-based TR Cutler Cameron Reddish Blue Devils Jersey , Inc. (www.trcutlerinc), is the nation's leading manufacturing journalist. Cutler is the founder of the Manufacturing Media Consortium of 2000 journalists writing about trends in manufacturing. Cutler is the lead spokesperson for the ETO Institute (www.etoinstitute.org). Cutler is also the author of the Manufacturer's Public Relations and Media Guide. Cutler is a frequently published author within the manufacturing sector, more than 200 feature articles annually.
Encompix (www.encompix) has filled the manufacturing software requirements of Engineer-to-Order companies since 1992. The company name reflects the commitment to developing business application solutions that encompass the complex areas of project-based and job-based manufacturing. Encompix provides ETO manufacturers with a competitive advantage by improving bottom line results.
To ensure that your deck has a long, trouble free life, it's important to use the right fixings used to fix the planks to the bearers. This choice can be influenced not only by the prevailing climatic conditions, the proximity to marine environments Trevon Duval College Jersey , but also the actual wood used. As your deck will around for a long time, it's best not to compromise too much on the fixings as the higher cost of better quality products will be repaid many times over with a longer service life and better looking deck.
Normally, standard iron nails should not be used on external decking as they can rapidly corrode in certain climatic conditions or close to marine environments and not only leave black stains around the nail holes, but can eventually corrode so extensively that they will simply snap. Remember that all wood will twist and warp to some extent so its important that wood planks are firmly fixed to the bearers at regular spaced intervals to keep the timber from moving. If you wish to use nails Marvin Bagley III College Jersey , then you should use a good quality galvanized nail, recommended for exterior decking. Note that some species of lumber - in particular, Western Red Cedar, Merbau and Redwood - contain tannins that can cause corrosion to occur more rapidly than with other species of lumber.
If using screws to fasten the decking planks to the bearers Grant Hill College Jersey , then again you shouldn't use standard steel screws, but either stainless steel or good quality plated screws. But there are many different methods of plating screws and some of the cheaper products may look great in the packet when they're purchased but not so pretty after a few years of use. Plating may be only superficial at best and in the process of fixing screws into the plank, the plating can be damaged which allows corrosion to start from day 1. So it's important that you use a good quality plated screw and is specifically recommended for use on exposed decking.
For the best long term results, stainless steel screws will always be the best option. Although these screws can be significantly more expensive Harry Giles College Jersey , the extra cost will be repaid in their long life, their ongoing appearance and lack of blackening around screw holes. Note also that in marine environments, stainless steel screws should always be used, as even plated screws can be subject to significant corrosion problems in such harsh environments.
Apart from nails or screws Jayson Tatum College Jersey , other fixing devices are also available on the market. These devices generally rely on the metal fixture (typically galvanized iron) being driven into the sides of the planks rather than the top, and the fixing itself is nailed to the bearers. One of the obvious advantages of this fixing method is that there are no screws or nails visible on the top surface. However, one of the disadvantages of this particular fixing system is that if you need to replace planks at any time, it's very difficult to both lift up and replace any plank in the middle of a deck. Normally the replaced plank would need tobe fixed in a conventional manner with nails or screws. Fortunately such replacements are rarely needed so Brandon Ingram College Jersey , this may not be such an important issue.
Insurance Talk
Thema drucken
24.03.2020 07:38
Antworten
